Denver DVBT-11 Instruções de Operação descarregar pdf (Página 3)

Note:

– If the LED flashes six times, the code was not recognised. Please go back 

to step 1 and repeat the procedure, using the next 6-digit code in the list.

– If no key is pressed within 10 seconds, you have to start again at step 1.

– If no correct code is in the list, try using “Automatic Code Search”.

Set up by Automatic Code Search

If you cannot identify a correct Device Code for your TV or satellite receiver

from the Device Code List, you may try our Automatic Code Search method:

1. Be sure your device is switched on.

2. Aim your remote at the device. Press and hold down “ ” and “ ”

 simultaneously until the indicator lights up.

3. Enter a corresponding Magic Search Code from the following table. The 

indicator should go out immediately.

Note:

– Each time you press or , the URC will skip to the next code and 

send out a POWER signal trying to turn off your device.

– If the indicator flashes 6 times after you pressed of key, you are 

already at the last code of the library. The search mode will then exit 

automatically.

– “ ”, “ ”, “ ”, “ ” and “ ” can still be functioned if the 

remote control is in search mode.

By Learning Commands

Your URC is factory pre-programmed to operate your TVs, SATs and DVB-T boxes.

Due to the limited number of keys, some minor functions may not be included.

You may teach your URC with the original A/V remote to operate any excluded

function by your choice.

1. Press and hold down “ ”, “ ”, and “ ” key for 2 seconds until 

the indicator lights up.

2. Aim your A/V remote control to the URC Infra-red lens on a flat surface, with 

4-8 cm apart. Make sure your A/V remote control is with fresh batteries.

3. Press and release a desired key on the URC you want to hold the command. 

If no key is pressed for more than 10 seconds, the indicator will flash six 

times then turn off.

4. Press and hold the corresponding key on your A/V remote control to transfer 

the command. The indicator will flash once and keep on, the command has 

been learnt successfully, you can release the key on the A/V remote control. 

If the indicator flashes 6 times, it shows error in learning process. Adjust 

the position of both remote controls and repeat steps 3 to 4 again.

(e.g. Press TV device mode key, then press “ ” and “ ”, and enter 

TV Search Code 000001.)

4. Press and hold down “ ” and “ ” until the indicator lights up.

5. Press key repeatedly and patiently. Once the correct code is found, the 

device switches off automatically.

6. Press and hold down “ ” key to lock in code and the indicator should go 

out.

SAT

English

P VOL

DEVICE TYPE:

MAGIC SEARCH CODE:

000001

SAT

000003

P VOL

3 LEARNING

VOL

SAT

TV/AV

3 4

English

Note:

– If the indicator flashes 6 times after you pressing of key, you are already 

at the last code of the library. The search mode will then exit automatically.

– Do not attempt to learn additional commands with the “ ” key as it will 

not hold commands by itself.

– Please be noted that learning function will not be performed if the URC is 

low on battery.

– Each function key will hold one command only. Learning a new command 

will automatically replace the previous one.

Advance Learning – Teaching a Dual Signal

If you found a learned command work for your A/V equipment only occasionally,

your original remote control may contain dual signals.

Try the following steps to reprogram this command:–

1. Follow step 1 and 2 of section “By Learning Commands”.

2. Press and release a desired key on the URC you want to hold the command. 

Now, the indicator will flash once and then keep on.

3. Press and hold the corresponding key on your A/V remote control to transfer 

the command. The indicator will flash once and keep on.

4. The first signal has been transferred successfully and you can release the 

key on the A/V remote control.

5. Press the same button on the URC again. The indicator will flash once and 

then keep on. The dual signal command has been transferred successfully.

6. Repeat step 2 to 4 of this procedure to transfer other signals if there is any.

7. When finished, press “ ” to store your setting. The indicator will turn off.

WARNING:

Entering a new pre-programmed Device Code will automatically erase and

replace all learnt commands in the chosen device mode.

Macro Power allows you to turn two of your A/V equipment on/off simultaneously.

To initiate this function, press “ ” on/off after the URC setup.

4 MACRO POWER

Once you have set up your URC, it should work like your original TV or SAT/DVB-T

remote control.

To operate, just aim the URC at your device and press the appropriate key for

whatever function you wish. (i.e. “ ”, “ ”, “ ”, “ ”)

Important note for turning on your TV:

There are some TVs which only can be turned on by pressing a direct channel

key. Since your URC does not have direct channel buttons, you need to press

“ ” to turn on your TV and press to switch off.

5 OPERATING THE URC

P P VOL VOL

5. Repeat step 3-4 to transfer other signals into next function key. When you 

finish the whole device mode, press “ ” key to store your setting. The 

indicator will flash six times then turn off.

1 2 3 4 5 6 7 8

Comentários a estes Manuais

Sem comentários

Denver DVBT-11 Instruções de Operação Página 3

Comentários a estes Manuais